OVERVIEW
The 3.2-liter VTEC-equipped engine is compact, lightweight and
fuel-efficient, representing the next generation of Acura V-6
powerplants. The 60-degree, 24-valve V-6 is mounted transversely in
the chassis, improving packaging efficiency. It is coupled with a new
5-speed Sequential SportShift automatic transmission with Grade Logic
Control that drives the front wheels with the assistance of a
standard Traction Control System (TCS).
Performance
- 225 horsepower at 5,600 rpm
- A broad torque curve provides 216 lbs.-ft. @ 4100 rpm
- VTEC increases low rpm torque and high rpm horsepower
- Automatic transmission with 5-speed Sequential SportShift allows semi-manual operation
- Compact, lightweight powertrain is 18 percent lighter than previous generation
Emissions/Fuel Economy
- EPA fuel economy 19/29 mpg (city/hwy)
- All 2001 3.2 TLs meet LEV standards; California models meet ULEV standards
Noise Vibration and Harshness (NVH)
- Smooth running 60-degree V-angle
- Full-floating piston pins eliminate piston slap during warm-up
- Elimination of separate camshaft holders allows for a more compact, rigid cylinder head
- Lightweight pistons and connecting rods
- Three hydraulic engine mounts
- Cast aluminum oil pan
ENGINE ARCHITECTURE
The TL is powered by a new-generation 3.2-liter, 225-hp, 24-valve V-6
engine. Remarkably compact and lightweight, the TL power plant and
transmission incorporate a wide variety of advanced technologies.
Relative to the previous-generation 1998 TL, total powertrain weight
has been reduced by 16 percent. The engine alone accounts for eight
percent of that weight reduction, no small feat in light of the
engine's improved power output, refined NVH characteristics and high
fuel economy.
ENGINE BLOCK
Die-cast and heat-treated, the compact aluminum block is extremely
rigid, with a high natural frequency and minimal resonant vibration.
The TL V-6's iron cylinder liners have their bore pitch set at a
close 98-mm spacing to reduce overall engine size. The free-revving
TL engine is oversquare with a bore of 89 mm and a stroke of 86 mm to
give the engine a total displacement of 3210 cc. The TL engine's
V-angle is 60-degrees -- a departure from the 90-degree V-angle used
in the previous-generation TL. This narrower angle improves
smoothness and reduces overall bulk and weight. Designed to work with
special compact pistons, the block has an unusually short deck
height, resulting in an overall reduction in the height and width of
the assembled engine.
CRANKSHAFT/CONNECTING RODS
The pursuit of compact overall engine dimensions coupled with Acura's
high durability standards drove the design of the TL crankshaft and
connecting rods. A rigid, forged crankshaft and narrow 19 mm
connecting rods allow for a reduction in overall engine length, and
are a contributing factor in making the TL powerplant (as installed
in the car) narrower than its competition from Lexus or Infiniti,
even though it offers more displacement and torque. The TL's rods
don't use conventional nut-and-bolt type fasteners, but instead
employ lighter bolts (without nuts) called plastic-region fasteners.
These bolts are designed to operate in the plastic, not elastic,
region of the steel material, unlike conventional fasteners. This
allows a downsizing of the rod bolts while maintaining the proper
clamping force and strength margins.
CYLINDER HEAD/LOW-FRICTION VTEC VALVE TRAIN
With four-valve combustion chambers and a 9.8:1 compression ratio,
the TL pressure-cast aluminum alloy cylinder heads reflect Acura's
latest thinking in engine design. The single camshaft in each
cylinder head is installed from the side, eliminating the need for
bolt-on cam caps -- a savings of weight and complexity. Driven by the
crankshaft via a glass-fiber reinforced toothed belt, the cams
actuate the valves via friction reducing roller followers.
The Variable Valve Timing and Lift Electronic Control (VTEC) valve train is a major contributing factor to the TL's remarkable combination of high power delivery and fuel economy. With the lift and opening duration of the large intake valves altered automatically based on engine rpm, the engine develops strong low-speed torque without sacrificing high rpm power.
Conventional fixed intake valve timing can't equal this broad-range flexibility. The VTEC-equipped 2001 TL engine delivers the power expected of an engine its size at middle engine speeds, but substantially more horsepower from 4600 rpm through the 6300 rpm redline than expected, coupled with considerable torque increases both at low and mid rpm and at high engine speed.
At low rpm, the VTEC intake valves follow a set of low-lift, short-duration cam lobes with timing that optimizes cylinder filling. Additionally, the timing of the intake valves are staggered and their lift is asymmetric, creating a swirl effect within the combustion chambers. This increases burn speed and improves combustion stability and EGR rate. As the engine accelerates through 3500 rpm, the intake rocker arms transition to actuation by high-lift, long-duration cam lobes designed to optimize high rpm output.
INDUCTION SYSTEM/PGM-FI
Controlled by a 16-bit, 32 Mhz Power Control Module (PCM) the TL's
PCM monitors throttle position, engine temperature, intake manifold
pressure, atmospheric pressure, exhaust gas oxygen content and intake
air temperature and tracks the operation of the engine with position
sensors on the crankshaft and both camshafts. The PCM controls the
5-speed automatic transmission. It controls fuel delivery to six
injectors mounted in the new cast aluminum, tuned-length intake
manifold. The intake manifold features a large plenum chamber to help
maximize air flow and increase power and torque.
EXHAUST SYSTEM
The TL high-flow dual exhaust system is designed to offer
lightweight, minimal noise and vibration and excellent emissions
control. Not only does the dual-exhaust design provide greater
performance, its compact design reduces intrusion into the cabin and
trunk areas.
DIRECT IGNITION SYSTEM/KNOCK CONTROL
Proper ignition spark timing is critical to engine performance and
emission control.
Unfortunately, the correct ignition timing is a moving target, changing from one instant to the next depending on a multitude of factors. Too little spark advance for the conditions and efficiency suffers; too much and the onset of knocking (or pinging) can result in overheating and engine damage. To ensure a properly timed spark, the TL relies on a new generation knock-control system. Based on a centrally positioned sensor in the block that "hears" the first traces of knocking, the ignition timing is advanced to the point of peak efficiency, but not beyond, even if fuel quality is less than the specified unleaded premium. This fine spark control allows the TL to operate safely --- and more efficiently -- with greater spark advance than its predecessor.
Another refinement to the ignition system is the adoption of improved direct ignition coil units, which are positioned directly in the spark plug access bores. Less than half the weight of the units used on the previous-generation TL, the direct coil units are more compact and more reliable.
CONTROL OF NOISE, VIBRATION AND HARSHNESS
During development of the Acura V-6 powertrain, special effort was
devoted to attaining higher standards of Noise, Vibration and
Harshness (NVH) control. Key competitive engines were analyzed to
develop engineering targets for smoothness and noise control. The
engineering exhibited in the TL reflects this effort with features
like the compact, rigid aluminum block and its unusually high
resonant frequency, rigid forged crankshaft, die-cast accessory
mounts and stiff cast aluminum oil pan.
100,000-MILE TUNE-UP INTERVALS
The TL's first scheduled tune-up is required at 105,000 miles; during
that time only routine inspections and fluid changes are required.
The roller-follower design of the VTEC valve train cuts friction and
wear to the point that the screw-type tappet clearance adjusters need
not be checked until 105,000 miles, at which point the
platinum-tipped spark plugs are also due for replacement.
DIRECT-ACTING CRUISE CONTROL
When the cruise control is engaged, the cruise control PCM directly
commands downshifts to the transmission as required, allowing the TL
to more closely maintain the set road speed even in hilly driving
conditions. The convenient steering wheel-mounted cruise control
buttons allow the driver to adjust speed in 1 mph increments or
disengage the cruise control without touching the brake pedal.
TRACTION CONTROL SYSTEM
Given the TL's formidable power output and the need for all-weather
drivability, a Traction Control System (TCS) is standard equipment.
This low-speed system operates at vehicle speeds below about 25 mph
by applying one or both front brakes to control wheelspin when
necessary. This independent wheel control provides a limited-slip
differential effect that substantially improves performance on
surfaces with split traction coefficients. Relative to the previous
generation TL, which used throttle control only to limit wheelspin,
the new TL delivers up to 30 percent better acceleration and climbs
hills much more easily in start-up split-traction situations.
5-SPEED SPORTSHIFT AUTOMATIC TRANSMISSION
Though advances in usable engine power output play a significant role
in the TL's quick acceleration, its 5-speed automatic transmission
figures heavily in measured performance gains and seat-of-the-pants
driving feel. Its gear ratio settings closely match the demands of
varied driving situations. Plus, the transmission's tall 5th gear
results in a lower cruising rpm for reduced engine noise and lower
fuel consumption. In the EPA highway driving cycle, the TL achieves
an impressive 19 city/29 highway mpg.
Linear solenoids provide precise, real-time control of the clutch on/off pressure in the TL's transmission. With superior clutch-engagement accuracy, the sophisticated control logic system operates smoothly under all conditions. To reduce noise, a bearing supports the idle shaft, and the gear-mesh contact ratio was refined. The wide lockup torque converter engagement area provides more positive engagement over a broader range of driving speeds.
Multiple safety and control strategies use interaction between engine and transmission controllers to manage overall powertrain operation. By limiting engine output torque and/or transmission clutch pressure, sharp driveline shocks are eliminated. The engine is also prevented from exceeding 5000 rpm in neutral and park.
GRADE LOGIC CONTROL
By monitoring throttle position, vehicle speed and
acceleration/deceleration then comparing these inputs with a map
stored in the transmission computer, the TL Grade Logic Control
System "knows" when the car is on a hill. The shift schedule is then
adjusted automatically to hold the engine in a lower gear for better
climbing power, increased downhill engine braking and decreased shift
frequency.
SEQUENTIAL SPORTSHIFT
To complement the TL's sporting nature, the standard automatic
transmission features a sequential SportShift mode similar to the one
originally introduced in the NSX sports car. Although somewhat
different in design, the SportShift mode puts gear selection in the
hands of the driver, much like a manual transmission. By moving the
console-mounted transmission selector handle to the left of the drive
position into a special SportShift gate, upshifts and downshifts can
be commanded with a quick fore or aft motion. Gear selection is
indicated by an LED display positioned prominently in the tachometer
face.
To foster the immediate feel of a manual transmission, in SportShift mode, the transmission logic commands firmer shifts that are approximately 10 percent quicker than in automatic mode. Additionally, the system is engineered to deliver an unusually quick response time to shift commands as compared to other semi-manual automatic transmissions.
Typically, the TL's transmission responds to a shift command in just 0.35 second, with the total shift completed in just over 0.9 second from the initial lever movement. These figures are quicker than those of semi-manual automatic transmissions of sports cars costing more than twice as much as the TL.
The SportShift system parallels the operation of a manual gearbox, with built-in safety override features. The logic will not allow a downshift that would cause the engine to over-rev in the driver-selected lower gear; the transmission will stay in the selected gear until the vehicle comes to a complete stop and then will shift into first should the driver forget to do so. During acceleration, except for shifting between 1st and 2nd, the transmission will not up-shift automatically in SportShift Mode.